irfp MOSFET are available at Mouser Electronics. Mouser offers inventory, pricing, & datasheets for irfp MOSFET. IRFP Vishay Siliconix | IRFPND DigiKey Electronics IRFPPBF; Vishay Siliconix; MOSFET P-CH V 12A TOAC; Unit Price $ IRFP Power MOSFET P-channel TOAC V 12 A Item-No.: IRFP €1, incl. VAT. excl. Factory number: IRFPPBF. Package weight.

Author: Malaktilar Mikajinn
Country: Turkey
Language: English (Spanish)
Genre: Automotive
Published (Last): 6 August 2008
Pages: 207
PDF File Size: 9.92 Mb
ePub File Size: 8.5 Mb
ISBN: 266-7-57276-675-7
Downloads: 74776
Price: Free* [*Free Regsitration Required]
Uploader: Faurg

Thanks for the help.

Technical Details

What is the purpose of the resistors R1 and R8 being variable? Amplifier Circuits Audio Circuits. Usually ships within 4 to 5 days. Once things are fine set current adjusting pot to minimum value switch on with new MOSFETS and with a dummy load of 25 ohms without speaker.

IRFP , power MOSFETs – elpro Elektronik

Your email address will not be published. View Cart Proceed to checkout. Which are the resistances burnt. There’s a problem loading this menu right now.

Thank you sir, god bless you.

irffp Be the first to review this item 0. C1 is used to take care of HF decoupling, as C2 is wound capacitor with inductive componunt and for LF decoupling. This amplifier will burn. Amazon Second Chance Pass it on, trade it in, give it a second life.

IRFP9240 “original” Vishay MOSFET Transistor 2 Pcs

Feedback If you are a seller for this product, would you like to suggest updates through seller support? Amazon Music Stream millions of songs. Write a customer review. Sir, Can you please provide the PCP layout. The spec is given below, also I have some doubts regarding the project. If 6A ampere bridge is not available, then make one using four 6A6 diodes. Resistor R20 limits the input current to Q1 C7 bypasses any high frequency noise from the input. Hi Chiliman the bridge rectifier should be capable 25amps.


I need watts rms amplifier circuit diagram. Set R1 at midpoint before powering up and then adjust it slowly in order to get a minimum voltage less than 50mV0 at the output. If I power up six of these with the same power supply, what value should each rectifier diode have? Get to Know Us. A basic dual power supply is used for the amplifier circuit. Hi Theofrastos K logarithmic control that should take care for volume problem at lower settings, do not use Lin controls.

Transistor Q1 and Q2 forms the input differential pair and the constant current source circuit built around Q9 and Q10 sources 1mA. Hi you are correct it should be 33mV. Power amplification stage based on Q7 and Q8 which operates in the class AB mode.

Laliva 10PCS NEW IRFP IRFP TO3P V 12A – –

If no, then what should I change in power supply??? This amp will work, but you have to add a filter circuit at the input. AmazonGlobal Ship Orders Internationally.


The sound is superb. Can I use 20pf in place of c4 n c5?? If u have ideas about these please share. If things are ok set the current as recommended, and connect 8 ohms speaker and try. If heat sink temperature is used for thermal compensation it cannot be used. Hi, I have one question.

For warranty information about this product, 2940 click here. Try this W Hi-Fi mosfet Amplifier http: Capacitor C8 is the input DC decoupling capacitor which blocks DC voltage if any from the input source.

I think preamp will just only increase the voltage level of the input signal, but when we split a signal into two actually the current is divided into two. For stereo you have to double the current of transformer. It can work with 4 ohms speaker delivering around watts. I need irf help…. Hope you have kept R1 at center and R8 at minimum value before switching on your amplifier.

I disconnected the circuit from mains quicker than the fuses.