Graupner: MC, MC, MC, MC, MC, MC, MC, MC/20, es in Übereinstimmung mit dieser Anleitung mit vorgeschriebenr Spannung. Bowdenzuginnenrohr auf 15mm ab und kleben diese mit Sekundenkleber in den passen Sie den Ausschlag über den Sender an (Computersender der mc. Thank you very much for purchasing the Graupner mc HoTT .. 15 / _jh_V1_de. PC COM Port connection. Through this socket it is also possible to.
|Published (Last):||12 November 2013|
|PDF File Size:||11.17 Mb|
|ePub File Size:||2.44 Mb|
|Price:||Free* [*Free Regsitration Required]|
This permits independent adjustment of the aileron deflections upward and downward, which allows a differential mixer to be used.
GRAUPNER mc-16 Programming Manual
If I could find wit a long or flat arm wheel be nice. Page 63 Helicopter Throttle Curve Throttle Curve Low, Middle, High access via Set-Up Menu Three different profiles for the carburettor response Setting can be adjusted and called up in flight by external After grsupner of the point required using the switches; the function of the throttle pre-select is button and operation of the appropriate CH SEL included in this changeover.
Page 29 Fixed Wing Models Descending Flight Setting Alternative Flight Setting Important Notes During the previous setting it was assumed that any For special applications you can program an Before starting the engine you should make sure that external switches possibly attached for throttle and alternative flight setting, which can be switched to throttle selector switch is in the start position, pitch curve change-over were in the basic position, Page 97 This is fitted next to the receiver.
All 8 switches have a functions by using 2 channels to make central position, which makes it 8 channels. Any information is valuableso Please feel free to share with me what ever You have.
Both surfaces of the V-tail move in the same direction. Page 55 Fixed Wing Models Al I need is what type of components are suitable for and If is necessary to make some settings on it. Operating Instructions Operating Instructions The resistance to movement of the control stick can Opening the Anlietung case Changing the proportional control sticks and changing the centring force.
General Permissions Transmitter and Receiver for the 27 vraupner 40 MHz bands are registered and can be used without charge. Receiver outputs 5 and 8 are available for auxiliary functions, e. By pressing ‘print’ button you will print only current page. General permission for a Radio concerning the remote ggraupner of models Auxiliary information for manufacturers, trading companies, system approvals, Saarbrucken, for examination, and the salesmen and purchasers examination anleihung that the design corresponds to the appropriate technical regulations FTZ guideline 17 R for If so do you think it can be somehow send to me on email address?
So, I will get the switch and trim the lever down so I can slip a brass tube over it.
GRAUPNER MC / 40MHz – RC Groups
Page 7 or recharge. I know is possible because I opened the case and I see these ]http: You can use a fairly wide range of pots with the set, I find pots from 5kk work just fine with the set. For the 3-way switches oder potentiometer use pin 1 and 3 the anlejtung ones to pin 1 and 5 the outer ones at the 5-pin connector and pin 2 middle one on pin 2 or 4 on the 5-pin connector, turning the connector means reversing the channel.
Got it, continue to print. I have an MC19s.
Page 87 nc Page 94 Dimensions max, ca. Other batteries to a maximum of 30V can be connected with a cable Part No.
Graupner Mc 15 Bedienungsanleitung Huawei
What can I cm Operating Instructions The resistance to movement of the control stick can Opening the Transmitter case Changing the proportional control sticks and changing the centring force. I thought maybe was made only pieces and nobody cares to put on internet some info.
Yes You are right and it’s a good idea.
Page of Go. Many Thanks in Advance. All connectors are 2. Page 45 Fixed Wing Models Page 24 Example 2: Also included is a ready made mixer for Elevator Flap mixing. A switch connected to socket 7 of the transmitter board, allows this function to be changed between two options “SF0”