MP40 Data Sheet, application/pdf, MB, 08/06/ VorTech MP40w ES Propeller Pump Gen 2 MP40 Manual, application/pdf, MB, 10/27/ Your vortech propeller pump before you start, Adjust the pin spacer • Read online or download PDF • EcoTech Marine Gen 2 MP40 User Manual. MP40w ES. MP10 ES/ MP10w ES. For the full VorTech Pump manual, please visit our website at • Read this manual before installing .
|Published (Last):||1 July 2008|
|PDF File Size:||16.93 Mb|
|ePub File Size:||14.7 Mb|
|Price:||Free* [*Free Regsitration Required]|
This will come in handy if Page 33 – Section 5. Specifications and Operating Parameters Flow: Pump Disconnect Error Prote These modes operate automati- cally depending on the settings that you define.
EcoTech Marine Gen 2 MP40 User Manual
The parts store offers the mxnual commonly ordered service parts 24 hours a day, seven days a week. Specifications and Operating Parameters. Don’t have an account?
If none of this works, contact EcoTech Marine to speak with a service represenative. Advanced EcoSmart Pump Posi- tioning. Go into Feed Mode by holding the Mode button for three seconds. Page 16 Page 17 – Section 3.
Powering Your EcoSmart Driv Soaking these parts in a manuual acid solu- tion such as vinegar may be necessary if there is an extreme amount of calcium buildup.
Enter text from picture: It may then be cleaned of any obstructions. Appendix Page 43 – Section 8. Operational Modes Night Mode Time: Any water allowed into these components can damage them enough to require replacement.
MP10’s Aren’t Just for Nano Maintenance Full Driver Memory Clear In order to clear out a saved wave you must perform a full memory clear on the master driver. The VorTech pump is designed to operate with a constant gap between both halves of the device.
Place the pump sufficiently high enough above a fine sand bed so that sand is not blown around by the output or undertow created by the VorTech.
In some cases, an entire aquarium can be destroyed. While normally you cannot change the speed of a slave pump, because the speed is determined entirely by the master pump, with the EcoSmart driver you now have the ability to control the maxi- mum speed of individual slave pumps independently from the master.
Page 23 Short Pulse Mode can then be used if you would like a wave running all the time, or you can use an EcoSmart mode which will auto-load your saved wave frequency and use it during points in the EcoSmart program. Follow the sequence outlined in the diagram below to utilize the Auto-Tune function in simulating a wave in your reef tank environment. The EcoTech Marine Battery Backup sold separately combined with your VorTech pump is a unique accessory which greatly improves your likelihood of emerging from a power outage condition without any loss of livestock.
Setup Your Vortech 5.
Your VorTech propeller pump. Mnual adjusting the pin spacer, be sure not to bend the pins as they are inserted into the holes within the heat sink as this may permanently damage your VorTech. Operational Modes Feed Mode Time: Retry Firmware Upgrade Process.
Lowest Speed of pump Complain wrong Brand wrong Model non readable. The dim LEDs showing the speed setting. Because there are no other panes of maunal to place additional pumps, slave pumps should not be run in the turquoise mode at all for an aquarium with this configuration.
Ecotech Marine EcoSmart User Manual
Similarly to the MP40w, the MP10w comes with the EcoSmart Wireless Driver that enables wireless coordination and enhanced functionality between multiiple With all the electrical components outside the aquarium and a variety of easy-to-program modes, the VorTech is the saf- est, most versatile pump on the market. Page of 44 Go. Operational Modes Page 19 – Section 4.
Notes on placement The VorTech creates over 3, gallons per hour of low velocity flow within your aquarium. Page 14 – Section 3. By pressing ‘print’ button you will print only current page. EcoTech Marine shall not be held liable for damage to any aquarium, aquarium life forms, or other personal objects due to improper use of the device.
Any wa- ter allowed into these components can damage them enough to require replacement. Pump Configuration for EcoSma Page 34 For this tank we recommend that you place the master pump running an EcoSmart mode on the right end of the back pane of glass, and a slave pump on the left side.
Once they are all out, your Battery Backup is out of power and your pumps will no longer function until power is restored from the wall. Assigning Local Max Speed t