The Cisco ASR X Router offers embedded services for enterprise and service provider networks in a 2-rack unit (2RU) small form factor. It is integrated with. ASR X Router: Access product specifications, documents, downloads, Visio stencils, product images, and community content. Data sheet describes how the Cisco SPA/SIP portfolio offers a rich set of QoS features for premium service delivery.

Author: Migor Grokree
Country: Japan
Language: English (Spanish)
Genre: Marketing
Published (Last): 28 July 2009
Pages: 49
PDF File Size: 19.11 Mb
ePub File Size: 8.46 Mb
ISBN: 982-4-37469-242-7
Downloads: 87032
Price: Free* [*Free Regsitration Required]
Uploader: Yorr

Currently, two types of feature licenses are available. Use the static IP address vpn-static-ip you reserved earlier.

Community Tutorials

What is an ASR Router? The GCP will announce the prefix corresponding dafasheet your Cloud. Set to group16 as recommended configuration on ASR router.

Or, you datazheet leave it blank since the local subnet is the default. The default proposal associated with the default policy is used for negotiation. You must enter the same shared secret into both VPN gateways. The netmask length is recommended to be Remote network IP range — With four Gigabit Ethernet ports built in, it provides big branch offices with the power to manage all of the security features needed to run the communications necessary in a large corporation.

Before you begin Overview The configuration samples which follow will include numerous value substitutions provided for the purpose of example only. Click Create to create the gateway and initiate cusco tunnels, though tunnels will not connect until you’ve completed the additional steps below.

To increase the VPN throughput the recommendation is to add multiple Cloud VPN gateway on the same region to load balance the traffic across the tunnels. If an entire virtual device fails, Cloud VPN automatically instantiates a new one with the same configuration, so you don’t need to build two Cloud VPN gateways.

Be sure to use the inside interface on the ASR This name is displayed in the console and used cosco the gcloud command-line tool to reference the router. Please note that this guide is not meant to be a comprehensive overview of IPsec and assumes basic familiarity with the IPsec protocol.


Name — The name of the Cloud Router. IKEv2 Lifetime – set the lifetime of the datasheey associations after which a reconnection will occur. To get started with the Cisco ASR Series, refer to the detailed product part numbers and descriptions in the following tables: With these recommended settings, TCP sessions quickly csico back to byte IP packets so the 0102 will “fit” in the tunnel.

The ASR router run cef load balancing based on source and destination ip address hash, each VPN tunnels will be treated as an equal cost path by routing, it can support up to 16 equal cost paths load balancing. It must belong to same subnet as the GCP-side interface. It can be configured with your choice of a 5-gigabyte per second or a gigabyte per second embedded services processor.

DPD — set the dayasheet peer detection interval and retry interval, if there are no response from the peer, the SA created for asd peer is deleted.

In order to have symmetric traffic flow make sure that you set the priority of your secondary tunnel to higher value than the primary tunnel default priority is They comprise the memory, hard disk, and USB flash memory token. Although you must make a selection, your choice of 100 part number has no effect on the Cisco ASR Series Routers.

This comprison show you the models. Cisco ASR configuration The ASR router run cef load balancing based on source and destination ip address hash, each VPN tunnels will be treated as an equal cost path by routing, it can support up to 16 equal cost paths load balancing.

Cisco ASR Router Datasheet and Installation

Any references to IP addresses, device IDs, shared secrets or keys account information or project names should be replaced with the appropriate values for your environment when following this guide. The region must be the same as for the tunnel. To enable a set of required features, one of the following three technology packages is required: It consolidates up to customized packet-processor cores MHz to 1.


Association with the IPsec security association datasyeet done through the tunnel protection command.

Cisco ASR Router. The 2 VPN ssr configuration example here is built based on the IPsec tunnel and BGP configuration illustrated above, can be expanded to more tunnels if required. A security association is a relationship between two or more entities that describes how the entities will use security services to communicate securely.

To advertise additional prefixes to GCP, copy the “network” statement and identify the prefix you wish to advertise.

Please refer to the troubleshooting ASR1k made easy for. This value cannot be changed after the tunnel is created because it is used in the IKE handshake. There are two ESP models: Actually, you may be strange to the ASR Series because these routers always work for a carrier or service provider or a very large enterprise. During the IPsec SA negotiation, the peers agree to use a particular transform set for protecting a particular data flow.

Unlike earlier versions where awr problem with one process could crash the whole system, this modular design should help contain faults. Create a custom VPC network.

However, we must rely on these routers when connecting the WAN Internet. If the VPN gateway device on the other side of the tunnel doesn’t generate one automatically, you can make one up. Make sure the prefix is present in the datasheeh table of the ASR with a valid next-hop.