Find great deals for Cisco Catalyst R – switch. Shop with confidence on eBay!. Find great deals for Cisco Catalyst R – switch Cisco Catalyst R-E – switch. Shop with confidence on eBay!. This article describes that installation of a Cisco Catalyst R-E switch, including two Supervisor Engines II (WS-X+) and a 48 port Gigabit PoE module.

Author: Mikajin Yohn
Country: French Guiana
Language: English (Spanish)
Genre: Environment
Published (Last): 25 September 2008
Pages: 333
PDF File Size: 14.38 Mb
ePub File Size: 5.42 Mb
ISBN: 857-8-42026-705-1
Downloads: 58063
Price: Free* [*Free Regsitration Required]
Uploader: Toktilar

As shown above, the Supervisor engine passed all tests and then proceeded to boot the IOS. These are actually three very large electrolytic capacitors – quite impressive!

Problem with Cisco R – Cisco Community

Trending Price New. At the back left side of the board, you can see the supervisor engine’s connector which is equally impressive with pin connectors – 50 on each row!

The Supervisor Engine sockets extend to the far right to a total of three sockets per Supervisor Engine:. Depending on how the switch is intended to be used, it can be populated fully with 48 Gigabit PoE ports, providing full PoE to all 5 line cards — a total of ports where each line card can draw a maximum of Watts.

The upper area of the picture is where you’ll find the two large cube slots for the power supplies. Our understanding is that this rail of PCB with transistors and other electrical circuits mounted on it seemed to be regulators for the PoE support. Currently, the Supervisor Engine 6-E is the best performing engine available, providing Gbps bandwidth full duplex and million packets per second forwarding rate! Once the Supervisor engine bootup process is complete, you are able to configure any aspect of the switch according to your needs, just as you would with any other Cisco Catalyst switch.


This attracted our attention as we thought something very senstive must be in that area for Cisco to protect it in such a way. The power supplies installed were rated at Watts each – providing more than enough juice to power a significant number of IP Phones via the PoE cards installed later on.

Previous post Next post. Best Selling in Network Switches See all.

What’s The New of Cisco Catalyst 4507R+E and 4510R+E Chassis?

Refer to your software release notes for the minimum software release versions required to support the supervisor engines. Cisco Catalyst R – switch Be the first to write a review.

Examining the design and construction of the chassis, line cards and Supervisor Engines shows how much thought and work have gone into the product. When the R-E is switched on, both engines will boot by first performing a POST test on their modules, memory buffers etc.

Because we couldn’t wait any longer, we quickly opened one of two power supplies and inserted it into the designated slot. After opening the package and removing the plastic wrapping, we placed the switch on clsco floor so we could take a better look at it.

Forming the backbone for Cisco Catalyst enterprise networks, this product from the Cisco E-series is extensively used for campus and distribution deployments. To facilitate nonstop operations, the new chassis have two dedicated slots for supervisor engines. Obviously the most critical cards are the Supervisor Engines, generating most of the heat under intensive workload.


We took another picture inside the chassis to make things as clear as possible:. On top is the editor’s Chris Partsenidis laptop with a familair website loaded, Firewall. Network redundancy and built-in fault tolerance also reduce your risk of unplanned downtimes, which could adversely impact worker productivity. Improving on the most vital aspects of the Catalyst series, this Cisco Catalyst E-series chassis-based switch is backward compatible with past generations and architected to accommodate future versions.

At the back of each power supply, as expected, we found one long connector, split into three groups, the middle group containing pins which are barely visible in the picture:. Taking a look under the protective shield we found a PCB board that ran along the length of the board:. Network Administrator Savvas Filippidis gets ready to install a line card. Supervisor Engine 7-E vs. Articles To Read Next: Moving to the front side of the Supervisor Engine, you can see the part number and description:.

Installation of a Cisco Catalyst 4507R-E Layer 3 Switch

The chassis has two slots for supervisor engines for non-stop performance supporting both AC and DC power supplies. This command gives a report of the installed modules cards in the catalyst switch along with a few more details:. We saw areas of the switch which you won’t easily find elsewhere and our generous amount of pictures made sure you understood what the R-E looks like, inside and out!