Buy APC ACRC InRow RC Airflow Cooling System – kJ – CFM – Rack-mountable – Black: Electronics – ✓ FREE DELIVERY. Buy a APC by Schneider Electric InRow RC Airflow Cooling System. Unit M Get it online at a great price with quick delivery. Shop top Power and Racks at. The ACRC is a fully tested APC Inrow RC Chilled Water Cooling System ACRC The ACRC has been fully refurbished by
|Published (Last):||11 October 2014|
|PDF File Size:||7.62 Mb|
|ePub File Size:||18.49 Mb|
|Price:||Free* [*Free Regsitration Required]|
ACRC100 Operation and Maintenance Manual
Dimensions are shown in mm in. Route all piping 1 to the InRow RC in compliance with all local and national codes. LevelingThe alc feet provide a stable base if the floor isuneven, but cannot compensate for a badly slopedsurface. Stabilizing the EquipmentFloor bracketsTo prevent the equipment from moving from its final location if it is not joined with an enclosureusethe included bolt-down kit AR Page 20 Positioning the EquipmentService accessnaaAn acrc1000 of mm 45 in ofclear floor space in front and Failure to follow these instructions can result in injury or equipment damage.
Apply rubber- or plastic-based paints to concrete walls and floors. Circuit setters are required to regulate the flow of chilled water to each piece ofequipment.
Aoc weight equipment only This manual is available in English on the enclosed CD. Push the power cordsthrough the hole atthe top power cordentrance. Insulate the room to minimize the influence of exterior heat loads.
Apc-Schneider Electric APC-ACRC
Cross-reference symbol used in this manual See another section of this document Summary of the content on the page No. Recommended Accessories for Model: Page 26 Filling and PurgingWhen the equipment is properly piped, begin the filling process top piping configuration shown. If the system is to be set up as an isolated loop – a chiller.
Install the temperature sensor. Inspecting the Equipment Inspect for missing components. American Power Conversion Legal Disclaimer The information presented in this manual is not warranted[ Active flow controllers AFC. Failure to follow these instructions can result in equipment damage. The condensate drain line iscoiled inside the equipment, allowing you to route the condensatedrain line for either top or bottom use. Close the valves to a 3.
Top wiring configurationScrewsTop powercord entrance standard. Failure to follow these instructions can result in equipment damage. Why one should read the manuals?
Once the equipment is in its intended location, use a screwdriver to turn each le. Slightly open acfc100 top coil vent. All required maintenance can beperformed from the front or back ofthe equipment.
Route power cordsthrough theequipment to the toppower cord access,as acc100. Best Value We work hard to deliver a solution that fits your budget. Page 25 Condensate pump drain installation. American Power Conversion Legal Disclaimer The information presented in this manual is not warranted by the Xcrc100 Power Conversion Corporation to be authoritative, error free, or complete.
All shipped loose components are identified by part number anddescription on the bill of lading. This manual is available in English on the enclosed CD. Failure to follow these instructions can result in death, injury, or equipment damage.
Apply rubber- accrc100 plastic-based paints to concrete walls and floors. If the system is to be set up as an isolated loop – a chiller Summary of the content on the page No.
This manual is available in English on the enclosed CD. Polyethylene film is recommendedfor ceiling and wall applications.
Slightly open the top coil vent. Page 21 Stabilizing the EquipmentFloor bracketsTo prevent the equipment from moving from its final location if it is not joined with an enclosureusethe included bolt-down kit AR See theback cover of this manual for the part number.
Twojoining brackets are installed on the frontand rear acrc1000 the equipment.
A good user manual introduces us to a number of additional functionalities of the purchased item, and also helps us to avoid the formation of most of the defects. Secure the plate tothe underside of theequipment arcc100 withfour Phillips screws provided. Your manual failed to upload Positioning the EquipmentService accessnaaAn area of mm 45 in ofclear floor space in front and See the back cover of this manual for the part number.
Room PreparationDuring the design of the data center, consider ease of entry for the equipment, floor loading factors, andaccessibility to piping and wiring.
Depending onhow the holes on the joining brackets areused, you have the option of either inor mm spacing. For safety purposes, adequate personnel must be present when moving this equipment.
If damage has occurred, or if shipped loose parts are missing, report it immediately to the delivering carrier and note the problem on the receiving copy of the bill of lading. For GSA ordering assistance, call