editions of the Specification developed by AISI and CSA. AISI: for example, this Specification will be referred as AISI S, where the last. AISI SSERIES FRAMING STANDARDS BUNDLE. This bundle includes 11 documents. (Download). AISI S/S (). AISI S AISI. AISI-S General requirements for residential and commercial construction, prescriptive and engineered design. Examples include member identification.
|Published (Last):||17 January 2007|
|PDF File Size:||15.45 Mb|
|ePub File Size:||13.73 Mb|
|Price:||Free* [*Free Regsitration Required]|
The ends of a built-up compression member are connected by a weld having a length not less than the maximum width of the member or by connectors spaced longitudinally not more than 4 diameters apart for a distance equal to 1.
Cold-Formed Steel: SCREWS Self-Drilling Fasteners
ASTM C has historically stipulated manufacturing tolerances for cold-formed steel structural framing members. Leave a Comment Click here to cancel reply.
Six of these standards addressed the design of structural elements, such as general provisions, wall studs, floor joists, trusses, headers, and shear walls.
First Name Last Name. The discrete braces are limited to not greater than 8 feet 2. This article focuses on AISI S which applies to cold-formed steel structural members subject to gravity loading, wind loading, and seismic loading, except when specific seismic detailing is required. However, AISI S now incorporates an exception for a built-up axial load bearing section comprised of two studs oriented back-to-back forming an I-shaped cross-section.
This new chapter lists applicable AISI test standards for cold-formed steel framing members, connections, and systems. This new standard includes design provisions for wall systems, floor and roof systems, lateral force-resisting systems, as well as truss and header assemblies.
Free CFS Publications from the AISI/SMDI Construction Market Council
The truss component structural performance load test and full-scale truss confirmatory test methods, previously included in AISI S, are provided in this appendix. This chapter contains design provisions for cold-formed steel framing members and assemblies, as previously included in AISI S, S, S, and S The chapter also includes:.
This chapter provides installation requirements previously contained in the various framing standards.
Effective strip sisi model for steel-sheet sheathing. Beneficial for the design engineer is a new Effective Strip Method that enables the calculation of the nominal in-plane shear wall strength for Type I shear walls Figure 2. Your message Submit Comment. 2s00-07 limitation has been eliminated from AISI S; however, it should be remembered that mils is still the maximum thickness of standard products in the United States and 97 mils 0.
Also, for ease of use, S contains a section reference table between the S s20007 and the previous provisions Table 2. The use of ASTM E results in higher nominal shear strength values as compared with the cantilever test method historically used for steel s200-077 diaphragms. This chapter contains design, manufacturing quality criteria, and installation requirements for cold-formed steel trusses as previously included in AISI S This appendix contains requirements for the determination of the rotational stiffness that structural sheathing provides to framing members to facilitate the design for distortional buckling.
The effective strip method is permitted to be used within the following range of parameters:.
This method provides an alternative approach to determine the shear wall strength, especially for those that are outside the limitations of the tested systems. But, why would AISI develop six discrete framing standards as opposed to one design manual?
Free CFS Publications from the AISI/SMDI Construction Market Council –
From tothe AISI Committee on Framing Standards developed nine different framing standards to cover specific aspects of cold-formed steel framing. The previous design standards limited their application to framing members having a maximum base steel thickness to mils 0.
Section reference table S and previous standard.
Inthe manufacturing tolerance values were extended to the flange width and stiffening lip length. The other aosi addressed such topics as a code of standard practice, the definition of standard product, and prescriptive design for residential applications.
This new exception provides for a more economical w200-07 member, as is often used as a jamb stud or shear wall boundary member. The method assumes a sheathing strip carries the lateral load via tension field action. For roof aiwi floor diaphragms with a maximum aspect ratio of 4: For curtain wall systems, the standard now permits the use of the bracing combination of sheathing attached to one side of the wall stud and discrete bracing for the other flange Figure 1.
This has been an often asked question by framing design aidi. The exception applies where the built-up section is seated properly in a track, and the top and bottom end bearing detail of the studs consists of a steel or concrete support with adequate strength and stiffness to preclude relative end slip of the two built-up stud sections.
X200-07 computational method is applicable for walls sheathed with steel sheet. Sheathing and discrete bracing. It outlines the scope, which is for design and installation of cold-formed steel framing of a floor and roof systems, b structural walls, c shear walls, strap braced walls, and diaphragms to resist in-plane lateral loads, and d trusses for aixi purposes in buildings.
This newly developed chapter provides minimum requirements for quality control and quality assurance for material control and installation for cold-formed steel light-frame construction.
The simple reason is, it was easier to develop small single-topic documents versus a more comprehensive multi-topic document. These cold-formed steel framing standards are available as free downloads at www. Format defines design considerations.